冷轧厂酸洗机组3号横剪大流量中高压液压系统设计方案探讨

在宝钢２０３０ｍｍ冷轧厂酸洗机组中，为了满足厚规格ＩＦ钢的生产，拟将原有的气动式剪切机改成液压式剪切机。为此，设计了一套中高压大流量的液压系统以满足３号横剪大剪切力（最高达７００ｋＮ）和快速剪切（３秒／次）的需要。由于采用了蓄能器增速回路和二通插装阀控制技术，使该液压系统较传统的剪切机液压系统具有响应速度快、体积小、重量轻、发热少和降低电机能耗等优点。     

Fundamental solutions for half plane with an oblique edge crack

An elastic half plane with an oblique edge crack is considered in this paper. A pair of concentrated forces or point dislocations is assumed to act at an arbitrary point in the half plane. The half plane with an edge crack is first mapped into a unit circle by a rational mapping function so that the following analysis can be carried out on the mapped plane analytically. Then the complex stress functions are derived by separating the whole problem into two parts; one is the principal part corresponding to the infinite plane acted on by concentrated forces or dislocations, the other is the holomorphic part, which can be determined by making use of the property of regularity of complex stress functions. The stress intensity factors of the crack can be calculated with different inclined angles of the crack, and the displacement and stress components at an arbitrary position in the half plane can be expressed explicitly.     

钢筋钢纤维增强部分混凝土梁受剪性能试验研究

本文通过钢筋混凝土梁以及在受拉区部分地加入钢纤维的钢筋混凝土梁的试验及理论分析，研究了钢纤维混凝土层厚、钢纤维体积率和剪跨比对钢筋钢纤维增强部分混凝土梁受剪性能的影响，建立了与普遍钢筋混凝土梁受剪承载力计算公式相衔接的钢筋钢纤维增强部分混凝土梁受剪承载力的计算模型和计算公式．     

水闸闸室化算梯形横截面上不平衡剪力的分配计算

当地弹性地基梁法计算非岩石地基的水闸底板应力时，首先要求解出不平衡剪力，当闸墩截面选择梯形时（主要是边墩），常用方法是作图法，这既有误差又繁琐。所以就此推导出一个公式，可直接求解平衡剪力。     

异步时序型PAL解析方法的研究及解析结果分析

本文就异步时序现ＰＡＬ的解析，提出了一种状态图遍历算法。     

圆杆弹性和弹—塑性扭转公式的探讨

对圆杆在线弹性阶段，弹－塑性阶段和全塑性阶段的扭转剪应力的计算公式作了分析，并推导了在材料的应力－应变关系（τ－γ关系）不服从虎克定律时，扭转真实剪应力的计算公式。文中对扭转强度计算公式的来源，物理含义及其都作了详细的说明。这对执行和理解国家ＧＢ１０１２８－８８《金属室温扭转试验方法》是有益的，而且对高校中材料力学的教学具有一定的参考价值。     

Off-Optimum Cure of Aerospace Epoxy Adhesives

Four epoxy film adhesives used in aircraft manufacture and repair have been examined to establish the effect of deviation from the cure cycle specified by the manufacturer. In addition to the variation of the cure cycle, two surface preparations of the aluminium adherends (chromic acid etch or grit blast followed by silane treatment) were evaluated. Thermal analysis was used to examine the cure envelope of the adhesive, and its extent of cure and glass transition temperature. The adhesive properties were assessed by shear strength (in both single lap joints and in Iosipescu configuration), durability (Boeing wedge test) and chemical resistance to selected aggressive fluids. The sensitivity of the performance of a particular adhesive to offoptimum cure conditions depends on its composition and needs to be determined, not predicted.     

电动机笼形转子铸铝常见质量问题分析

在电机制造中，笼形转子三相异步电动机的转子铸铝质量的好坏直接影响电机的性能及力能指标。因此本文对常见的转子铸铝质量问题进行了分析，并提出了相应地解决措施，以获得优质的电机。     

一种高效的图像细化算法在焊缝跟踪中的应用

针对焊缝跟踪图像处理的特点，研究了二值化后的图像如何进一步细化的方法；采用先对焊缝的边缘进行提取，然后从垂直于焊缝的方向进行扫描的方法，取两条边缘的中点，即是焊缝的骨架；结果表明：此算法能准确地对一幅二值图细化，满足焊缝跟踪中图像处理的要求；这种算法的突出特点是计算量小，处理速度快，非常适合于焊缝的实时处理跟踪，而且不用改写算法，既适合于黑色背景白色图像，也适合于白色背景黑色图像.本算法通过推导得到四条处理准则，在遵循这几条处理准则的基础上逐点扫描图像，按照准则来确定目标点的删除与保留，达到细化的最终目的.     

黄埔发电厂#6发电机转冷水系统改造

黄埔发电厂#6发电机转冷水铜离子含量超标，通过对缺陷原因进行分析，针对二级水封的特性对溢出的转冷水进行回收并利用化学凝结水处理去除溶出的铜离子，通过控制转冷水的pH值最终减缓铜管的腐蚀.